A Micro Proportional Driver provides accurate control of hydraulic and pneumatic proportional solenoid valves used in mobile construction equipment and industrial processes. The MPD can control the flow of air or liquid linearly at a setting from 0.10-20 seconds. One example of use would be in a paint system. The MPD allows a solenoid to oscillate, significantly reducing system shock and wear commonly found in non-oscillation digital valve systems. The micro proportional driver is a compact electronic circuit built into an environment-resistant miniaturized enclosure. the circuit features control of proportional solenoids and operators. Functions include minimum and maximum current limiting, control signals from 0-10V or 0-20 mA (with a step function at 0.2V or 0.4 mA included for minimum current), a 0.1-20 sec. linear ramp up/ramp down adjustment and output current proportional to input command signal. This unit incorporates the DIN 43650 Form “A” / ISO 4400, EN175301-803:2000 connector male and female interface. The unit is mounted by use of a single mounting screw, DIN connector and two gaskets. Built to meet NEMA 4 environment standards, the MPD is made from engineered polymers for resistance to harsh chemicals and ingress of water or foreign substances. adjustments are made on the top surface of the unit. the unit can control any proportional solenoid valve operation within the values specified below using variable pulse width modulation.
This Canfield Connector miniature timer makes any valve, with the DIN 43650 Form “A”/ISO 4400, EN175301-803:2000 electrical interface, able to operate as a compressed air system condensate removal valve. The unit installs in a modular form between an existing coil and connector. No new wiring is necessary. Retrofits on virtually any installation. It works with the valve brand of your choice. The cycle and on times are easily adjustable and two indicator lights show status.
Canfield Connector’s Nylon Flex Strain Relief CanTop Connectors are a series of wire bulkhead feed through connectors which have integrated wire strain relief and sealing mechanism. These CanTops are made from rugged engineered materials which are impervious to dust and moisture. Available in various NPT, PG, and metric thread sizes and in Gray or Black Nylon. These CanTops are compatible with wire diameters from .079″ to .709″ to ensure a tight fit while enhancing any wire installation.
Canfield Connector’s Nickel Plated Brass Strain Relief CanTop Connectors are a series of wire bulkhead feed through connectors which have integrated wire strain relief and sealing mechanism. These CanTops are made from rugged engineered materials which are impervious to dust and moisture. Available in various NPT, PG thread sizes. These CanTops are compatible with wire diameters from .079″ to 1.732″ to ensure a tight fit while enhancing any wire installation.
Canfield Connector FAC connectors are DIN 43650 Form A & C, Industry Standard Mini, and 9.4mm solenoid valve connectors that adapt connection from M12 and DIN 43650 Form A, Industry Standard Mini 7/8 Automotive standard inlet connectors. Made from the finest materials in the USA, these connectors mate with distribution boxes in a quick connect manner making assembly a snap. They are available in 3 or 5 Pin 7/8 Automotive, 4 or 5 Pin 12mm molded and wired, with or without indicator lights & surge suppression.
The FAC series connectors are modular interface connectors made to conform to industry standard configurations. These connectors interface female ISO, MINI and Sub-Micro solenoid connections to industry standard male 7/8″ (MINI) and 12mm (Micro) circular connectors. These are as shown on the following pages. These rugged modular connectors offer rapid installation and environmental protection designed to IP 65 and NEMA 4. Options include indication LED, surge suppression and various pre-wired circuit configurations to connect with popular multi-port electronic interconnection systems and field-bus systems.
Canfield Connector’s R5000 Series solenoid valve connectors incorporate full-wave bridge rectifiers inside the DIN 43650 Form “A” / ISO 4400, EN175301-803:2000 connectors. This standard permits industry interchange-ability and has been embraced by the solenoid valve industry worldwide. The R5000 converts alternating current to direct current reducing coil burnout due to valve sticking. Also, direct current eliminates AC “hum” inherent to alternating current. Features include the ability for the user to wire the connector into existing installations. Wire connections are made inside the connector housing and the wire inlet is either PG9 strain relief, 3/8″ or 1/2″ conduit. The R5000 has a maximum current rating of 1 Amp continuous with maximum wire gauge diameter of 14 AWG. An indicator light is offered for instant diagnostics and to aid setup and installation.