5950 – Micro Proportional Driver

Standard

5950 - micro proportional driver

A Micro Proportional Driver provides accurate control of hydraulic and pneumatic proportional solenoid valves used in mobile construction equipment and industrial processes. The MPD can control the flow of air or liquid linearly at a setting from 0.10-20 seconds. One example of use would be in a paint system. The MPD allows a solenoid to oscillate, significantly reducing system shock and wear commonly found in non-oscillation digital valve systems. The micro proportional driver is a compact electronic circuit built into an environment-resistant miniaturized enclosure. the circuit features control of proportional solenoids and operators. Functions include minimum and maximum current limiting, control signals from 0-10V or 0-20 mA (with a step function at 0.2V or 0.4 mA included for minimum current), a 0.1-20 sec. linear ramp up/ramp down adjustment and output current proportional to input command signal. This unit incorporates the DIN 43650 Form “A” / ISO 4400, EN175301-803:2000 connector male and female interface. The unit is mounted by use of a single mounting screw, DIN connector and two gaskets. Built to meet NEMA 4 environment standards, the MPD is made from engineered polymers for resistance to harsh chemicals and ingress of water or foreign substances. adjustments are made on the top surface of the unit. the unit can control any proportional solenoid valve operation within the values specified below using variable pulse width modulation.

Advertisements

Sandwich CRT – Condensation Removal Timer

Standard

Sandwich CRT - condensation removal timer

This Canfield Connector miniature timer makes any valve, with the DIN 43650 Form “A”/ISO 4400, EN175301-803:2000 electrical interface, able to operate as a compressed air system condensate removal valve. The unit installs in a modular form between an existing coil and connector. No new wiring is necessary. Retrofits on virtually any installation. It works with the valve brand of your choice. The cycle and on times are easily adjustable and two indicator lights show status.

5800 – DIN Micro Logic Timer

Standard

5800 - DIN micro logic timer

The Canfield Connector micro logic timer is a solid state electronic timing unit incorporated inside the standard MINI and DIN 43650 Form “A” / ISO 4400, EN 175301- 803:2000 electrical connectors. The MLT allows precise timing and logic functions in a small, easily mounted enclosure. there are eight standard timer types. Each timer incorporates circuitry for AC or DC operation with a wide voltage range.

FAC – Automotive Standard to MINI or ISO

Standard

FAC - automotive standard to MINI or ISO

Canfield Connector FAC connectors are DIN 43650 Form A & C, Industry Standard Mini, and 9.4mm solenoid valve connectors that adapt connection from M12 and DIN 43650 Form A, Industry Standard Mini 7/8 Automotive standard inlet connectors. Made from the finest materials in the USA, these connectors mate with distribution boxes in a quick connect manner making assembly a snap. They are available in 3 or 5 Pin 7/8 Automotive, 4 or 5 Pin 12mm molded and wired, with or without indicator lights & surge suppression.

FAC – 12mm to MINI, ISO, or Sub-Micro

Standard

FAC - 12mm to MINI, ISO, or Sub-Micro

The FAC series connectors are modular interface connectors made to conform to industry standard configurations. These connectors interface female ISO, MINI and Sub-Micro solenoid connections to industry standard male 7/8″ (MINI) and 12mm (Micro) circular connectors. These are as shown on the following pages. These rugged modular connectors offer rapid installation and environmental protection designed to IP 65 and NEMA 4. Options include indication LED, surge suppression and various pre-wired circuit configurations to connect with popular multi-port electronic interconnection systems and field-bus systems.

MCCR – Multiple Control Distribution

Standard

MCCR - multiple control distribution

The Canfield Connector MCCR is a cable distribution connector which uses pass-through technology to allow control of multiple parallel or independent devices. Devised with double solenoids and solenoid valve manifolds in mind, the MCCR allows for simplified wiring and easy replacement of components in an automated, modular environment. The gasket-thin head fits between a single female connector and the associated male device with the DIN 43650 Form “A”, EN175301-803:2000 interface. Exiting from the MCCR head is a three conductor cable with ISO HT PG9 strain relief connector attached. Two available circuits allow for separate (independent) or parallel (simultaneous) control of the downstream device. The environment resistant quick connect style allows for plug and play designs in the factory that require modern hydraulic or pneumatic systems.

M5 – Male Quick Disconnect Interfaces

Standard

M5 - male quick disconnect interfaces

Canfield Connector male connectors are used as electrical quick disconnect interfaces for pneumatic and hydraulic valves and sensors. They are available in standard MINI, DIN 43650 Form “A” / ISO 4400, EN175301-803:2000, Sub-Micro 8mm, 9.4mm, and conduit arrangements. Some male connectors are available with 2+ ground or 3+ ground terminal options.