5950 – Micro Proportional Driver

A Micro Proportional Driver provides accurate control of hydraulic and pneumatic proportional solenoid valves used in mobile construction equipment and industrial processes. The MPD can control the flow of air or liquid linearly at a setting from 0.10-20 seconds. One example of use would be in a paint system. The MPD allows a solenoid to oscillate, significantly reducing system shock and wear commonly found in non-oscillation digital valve systems. The micro proportional driver is a compact electronic circuit built into an environment-resistant miniaturized enclosure. the circuit features control of proportional solenoids and operators. Functions include minimum and maximum current limiting, control signals from 0-10V or 0-20 mA (with a step function at 0.2V or 0.4 mA included for minimum current), a 0.1-20 sec. linear ramp up/ramp down adjustment and output current proportional to input command signal. This unit incorporates the DIN 43650 Form “A” / ISO 4400, EN175301-803:2000 connector male and female interface. The unit is mounted by use of a single mounting screw, DIN connector and two gaskets. Built to meet NEMA 4 environment standards, the MPD is made from engineered polymers for resistance to harsh chemicals and ingress of water or foreign substances. adjustments are made on the top surface of the unit. the unit can control any proportional solenoid valve operation within the values specified below using variable pulse width modulation.

Sandwich CRT – Condensation Removal Timer

This Canfield Connector miniature timer makes any valve, with the DIN 43650 Form “A”/ISO 4400, EN175301-803:2000 electrical interface, able to operate as a compressed air system condensate removal valve. The unit installs in a modular form between an existing coil and connector. No new wiring is necessary. Retrofits on virtually any installation. It works with the valve brand of your choice. The cycle and on times are easily adjustable and two indicator lights show status.

5800 – DIN Micro Logic Timer

The Canfield Connector micro logic timer is a solid state electronic timing unit incorporated inside the standard MINI and DIN 43650 Form “A” / ISO 4400, EN 175301- 803:2000 electrical connectors. The MLT allows precise timing and logic functions in a small, easily mounted enclosure. there are eight standard timer types. Each timer incorporates circuitry for AC or DC operation with a wide voltage range.

Nylon Flex Strain Relief Cord Grips

Canfield Connector’s Nylon Flex Strain Relief CanTop Connectors are a series of wire bulkhead feed through connectors which have integrated wire strain relief and sealing mechanism. These CanTops are made from rugged engineered materials which are impervious to dust and moisture. Available in various NPT, PG, and metric thread sizes and in Gray or Black Nylon. These CanTops are compatible with wire diameters from .079″ to .709″ to ensure a tight fit while enhancing any wire installation.

Nylon Strain Relief Cord Grips

Canfield Connector’s Nylon Strain Relief CanTop Connectors are a series of wire bulkhead feed through connectors which have integrated wire strain relief and sealing mechanism. These CanTops are made from rugged engineered materials which are impervious to dust and moisture. Available in various NPT, PG, and metric thread sizes and in Gray or Black Nylon. These CanTops are compatible with wire diameters from .079″ to 1.732″, to ensure a tight fit while enhancing any wire installation.

FAC – Automotive Standard to MINI or ISO

Canfield Connector FAC connectors are DIN 43650 Form A & C, Industry Standard Mini, and 9.4mm solenoid valve connectors that adapt connection from M12 and DIN 43650 Form A, Industry Standard Mini 7/8 Automotive standard inlet connectors. Made from the finest materials in the USA, these connectors mate with distribution boxes in a quick connect manner making assembly a snap. They are available in 3 or 5 Pin 7/8 Automotive, 4 or 5 Pin 12mm molded and wired, with or without indicator lights & surge suppression.

DCP – DIN Coil Pin Protectors

The Canfield Connector DCP coil pin protectors are low cost replacements for solenoid connectors that ensure protection of solenoid terminals during shipping and handling. They can also be used to protect spade style terminals on a variety of other products. DCPs are available in a host of colors and styles as well as special logo markings to match the application. Constructed of low cost yet rugged polymers, the DCP adds aesthetic appeal and advertising value to the solenoid valve. There is a DCP available for ISO, industry standard MINI, Sub-Micro, and dual spade hydraulic coils.

M5 – Male Quick Disconnect Interfaces

Canfield Connector male connectors are used as electrical quick disconnect interfaces for pneumatic and hydraulic valves and sensors. They are available in standard MINI, DIN 43650 Form “A” / ISO 4400, EN175301-803:2000, Sub-Micro 8mm, 9.4mm, and conduit arrangements. Some male connectors are available with 2+ ground or 3+ ground terminal options.

P5600 – Surge Suppression

The Micro Protective Connectors are available in standard MINI, DIN 43650 Form “A” / ISO 4400, EN175301-803:2000 and Sub-Micro 8mm and 9.4mm. The Canfield Connector MPCs provide electrical controllers surge suppression against voltage spikes caused by the solenoids used on hydraulic and pneumatic solenoid valves.