FAC – Automotive Standard to MINI or ISO

Standard

FAC - automotive standard to MINI or ISO

Canfield Connector FAC connectors are DIN 43650 Form A & C, Industry Standard Mini, and 9.4mm solenoid valve connectors that adapt connection from M12 and DIN 43650 Form A, Industry Standard Mini 7/8 Automotive standard inlet connectors. Made from the finest materials in the USA, these connectors mate with distribution boxes in a quick connect manner making assembly a snap. They are available in 3 or 5 Pin 7/8 Automotive, 4 or 5 Pin 12mm molded and wired, with or without indicator lights & surge suppression.

Advertisements

FAC – 12mm to MINI, ISO, or Sub-Micro

Standard

FAC - 12mm to MINI, ISO, or Sub-Micro

The FAC series connectors are modular interface connectors made to conform to industry standard configurations. These connectors interface female ISO, MINI and Sub-Micro solenoid connections to industry standard male 7/8″ (MINI) and 12mm (Micro) circular connectors. These are as shown on the following pages. These rugged modular connectors offer rapid installation and environmental protection designed to IP 65 and NEMA 4. Options include indication LED, surge suppression and various pre-wired circuit configurations to connect with popular multi-port electronic interconnection systems and field-bus systems.

DCP – DIN Coil Pin Protectors

Standard

DCP - DIN coil pin protectors

The Canfield Connector DCP coil pin protectors are low cost replacements for solenoid connectors that ensure protection of solenoid terminals during shipping and handling. They can also be used to protect spade style terminals on a variety of other products. DCPs are available in a host of colors and styles as well as special logo markings to match the application. Constructed of low cost yet rugged polymers, the DCP adds aesthetic appeal and advertising value to the solenoid valve. There is a DCP available for ISO, industry standard MINI, Sub-Micro, and dual spade hydraulic coils.

MCCR – Multiple Control Distribution

Standard

MCCR - multiple control distribution

The Canfield Connector MCCR is a cable distribution connector which uses pass-through technology to allow control of multiple parallel or independent devices. Devised with double solenoids and solenoid valve manifolds in mind, the MCCR allows for simplified wiring and easy replacement of components in an automated, modular environment. The gasket-thin head fits between a single female connector and the associated male device with the DIN 43650 Form “A”, EN175301-803:2000 interface. Exiting from the MCCR head is a three conductor cable with ISO HT PG9 strain relief connector attached. Two available circuits allow for separate (independent) or parallel (simultaneous) control of the downstream device. The environment resistant quick connect style allows for plug and play designs in the factory that require modern hydraulic or pneumatic systems.

M5 – Male Quick Disconnect Interfaces

Standard

M5 - male quick disconnect interfaces

Canfield Connector male connectors are used as electrical quick disconnect interfaces for pneumatic and hydraulic valves and sensors. They are available in standard MINI, DIN 43650 Form “A” / ISO 4400, EN175301-803:2000, Sub-Micro 8mm, 9.4mm, and conduit arrangements. Some male connectors are available with 2+ ground or 3+ ground terminal options.

R5000 – Full Wave Bridge Rectifier

Standard

R5000 - full wave bridge rectifier

Canfield Connector’s R5000 Series solenoid valve connectors incorporate full-wave bridge rectifiers inside the DIN 43650 Form “A” / ISO 4400, EN175301-803:2000 connectors. This standard permits industry interchange-ability and has been embraced by the solenoid valve industry worldwide. The R5000 converts alternating current to direct current reducing coil burnout due to valve sticking. Also, direct current eliminates AC “hum” inherent to alternating current. Features include the ability for the user to wire the connector into existing installations. Wire connections are made inside the connector housing and the wire inlet is either PG9 strain relief, 3/8″ or 1/2″ conduit. The R5000 has a maximum current rating of 1 Amp continuous with maximum wire gauge diameter of 14 AWG. An indicator light is offered for instant diagnostics and to aid setup and installation.

P5600 – Surge Suppression

Standard

P5600 - surge suppression

The Micro Protective Connectors are available in standard MINI, DIN 43650 Form “A” / ISO 4400, EN175301-803:2000 and Sub-Micro 8mm and 9.4mm. The Canfield Connector MPCs provide electrical controllers surge suppression against voltage spikes caused by the solenoids used on hydraulic and pneumatic solenoid valves.